While everything described in the OP's preparation and step-by-step list is good, this minor overlook can be critical to the overall system. Then the existing TV coax and the new coax would connect to the splitters two outputs. Sign up to join this community. The best answers are voted up and rise to the top. Stack Overflow for Teams — Collaborate and share knowledge with a private group. Create a free Team What is Teams? Learn more. How do I properly feed coax through an outside wall?
Ask Question. Asked 7 years, 7 months ago. Active 5 months ago. Viewed k times. Improve this question. Kermit Kermit 1, 3 3 gold badges 11 11 silver badges 24 24 bronze badges. Typically the connectors are added after the wire is pulled that way a wall insert is put in place and sealed. Are you planning on doing the same or will the connectors already be installed? Jack The connectors on one end will be in place; just the end that will be fed into the house to make sure I have a tight drill hole.
Add a comment. Active Oldest Votes. I'd drill from the inside out. Preparation inside Cut a hole in the drywall where you want the terminal. Drill through the wall with the installer bit. Remove the bit from the drill leaving it in the hole. Go outside and or have a helper connect the cable to the end of the installer bit. Back inside, pull the bit and cable back through the hole. Connecting the cable Fish the wire from the outside junction, through the newly drilled hole if you haven't already.
Weatherproofing Finish by sealing around the cable, where it enters the wall. Improve this answer. ThreePhaseEel Tester Tester k 74 74 gold badges silver badges bronze badges. On the outside, be sure to include a drip loop, where the cable turns down as it exits the wall so that it doesn't lead water in. TomG A drip loop is only required if the cable slopes toward the hole in the wall.
If the cable comes out of the wall and immediately goes vertically down, or slopes downward away from the hole. No drip loop is needed, since water does not flow uphill. Thanks, I should have qualified 'if the cable doesn't go down when it exits, be sure to include a drip loop' — TomG. Thomas You mean they use latex caulk instead of silicone caulk? However, the ideal placement for the distribution panel in your house may be different—for example, a furnace room, garage, or even a closet —depending on your needs.
Create an access point into the stud space above and below the panel as well as an access point into the stud area below the panel. Position the panel in an open stud area so that you can fish fresh lines into the panel with the least amount of effort. Attics, basements, crawlspaces, garages, and even closets are the most convenient and unobstructed passageways. In most cases, you can simply drill holes in the top or bottom plates and insert the wires without having to open up the completed wall surfaces.
Middle floors, however, that are sandwiched between completed floors, may be more difficult to install. The use of surface-moun t cables to connect such rooms to the rest of the house is a smart approach, but cutting and repairing holes in completed walls or even ceilings to run the wires is occasionally unavoidable in certain situations.
Attach the jacks and snap them into the cover plate, then coil the excess lines neatly within the distribution box to complete the installation. Each outlet has four lines, and each of those lines returns to the distribution box.
The keyhole saw should be used to cut through the drywall to make the aperture necessary for the installation of a low voltage electrical box. First and foremost, ensure that the area you want to drill into is free of any potential dangers before proceeding to the following step i. Place the tip of the auger bit into the cutout in the wall and drill through the bottom of the stud wall to obtain access to the crawlspace below while the wall is still open.
This will make it much easier to identify the location where the cable will be installed. Once the cable line is in place, connect one end of the cable line to the tip of the drill bit using a utility string before returning to the house. Slowly draw the drill bit and the cable line that has been connected to the drill bit back up through the hole. Slide the low voltage box into the drywall hole and tighten it down to prevent it from moving around throughout the installation process.
It is necessary to add an F-connector to the end of the wire before you can complete this portion of the installation. Install the F-connector on the back of the coax cable receptacle wall plate and screw the wall plate into the low voltage electrical box to complete the installation. If your house was built differently than others, and if your cable lines were installed in a different location than others, the following step may be different for you. Now that one end of the cable line has been placed, you may use cable clips to attach the remaining length of wire to the floor joists as you work your way closer and closer to the hole you just created, which is closest to the cable box.
A short piece of string should be tied to the end of the fish pole after you have arrived to the drilled hole. A short piece of string should be tied to the end of the fish pole after you have arrived at the drilled hole. It is necessary to attach an F-connector to this end of the cable before you can proceed to the next step of the installation.
At the time of installation of a new cable line, I label it with a paint marker so that if an emergency occurs and I need to disconnect my connections, I can be confident that the right cables are reconnected.
Learn why people trust wikiHow. Download Article Explore this Article Steps. Tips and Warnings. Related Articles. Author Info Last Updated: June 4, When working from an attic space, it will be significantly easier to access a wall space on the floor below by working either an interior wall or, the exterior wall that is on the gable end of the structure.
It will be next to impossible to drill downward under the portion of the roof that slopes to the attic floor, without a "right-angle drill". When working from a basement, inspection of the area in contact with the foundation or sill will be required.
Some exterior walls are more accessible above one basement wall than another due to the way floor joists are installed. Either way, room to drill up from below will be required, unless opening the finished wall above to drill down is acceptable. Cut the bottom straight portion off from a metal coat hanger. Clip one end at about a 45 degree angle to form a long "drill bit". Chuck the "bit" into an electric drill - with the 45 degree angle out - it will serve as the cutting edge.
From inside the living space, position the bit against the wall directly above if accessing from attic or below if accessing from basement the desired location of the service the cable will provide. Protect the wall with a thin piece of cardboard, etc. After that, drilling should be noticeably easier.
You may need to withdraw the drill and clip the end again to make a new sharp edge. Continue drilling until 6 inches Once through - do NOT pull the drill out - unchuck the "bit" and leave in place. Once 2 inches 5. If not it is possible that the drill bit aligned with a floor joist. Do not pull the bit out - but unchuck it from the drill instead and leave in place.
Go to the space into which the drill was boring. Locate the "bit". Remove any insulation in the general area to make the bit easier to locate.
If unable to locate the bit, repeat the drilling process after moving to a spot a couple of inches away from the first hole. While in the space drilled into, using the bit as a locator for the wall above or below as the case may be , select a spot TWO inches "back".
It is very important to know which direction "back" is. If the correct direction is chosen, it would be "back" into the wall space, as opposed to 2 inches 5.
Run the drill until 6 or more inches have been pushed into the hole. Verify that the bit is NOT protruding through the ceiling, doorway, floor space, etc. Mark the spot that "bit" is in and withdraw the bit completely. If the "bit" appeared where not expected, try again until successful.
0コメント