Unhook the handles from the filter cover. Engage hopper support pin. Turn off the machine. Flush dirt and debris from the debris hose and debris screen and out into the hopper.
Excessive heat can damage tanks and components. Remove the vacuum screen from the recovery tank and rinse the screen. M20 8- Home Find Page 38 5. Remove the recovery tank drain hose from the back of the recovery tank, then rinse the dirt and debris from the hose into the tank. Remove the hopper support pin and insert it into the storage tube. Then lower the hopper. Close the recovery tank cover. Place the solution tank drain hose nozzle next to a floor drain.
Page 40 7. Reinstall the solution tank drain hose onto the toward the solution tank drain. Close the solution tank cover s. Rinse the float sensor and the screen filter. Allow the solution tank to drain. Page Options 5. When finished cleaning, place the spray nozzle and wand back into their storage locations.
Press the bottom of the Spray nozzle switch to turn off the water supply. Page Vacuum Wand Option Disassemble the vacuum wand assembly and regulatory authorities for exposure return it to the storage bag.
Keep engine properly tuned. Reattach the vacuum hose to the hopper lift arm. Page Page Lubrication The engine oil capacity is is located next to the front wheel support. Page Hopper Lift Arm Pivots The torque tube grease fittings on the operator side of the machine are located beneath the fuel tank.
On the other side of the machine the torque tube grease fittings are located beneath the propel pump. Page Hydraulics left photo on the hydraulic fluid label if originally equipped with TennantTrue premium hydraulic fluid. Replace the hydraulic strainer outlet after every hours of operation. Substitute fluids can cause premature failure of hydraulic components.
Hydraulic components depend on system hydraulic fluid for internal lubrication. Page Engine Location of drain cock on gasoline machines for machines serial number and below.
Remove the panel from operators compartment to access the drain cock. Flush the radiator and the cooling system after every hours of operation. M20 9- Home Find Keep area well ventilated. Location of fuel filter on machines serial number and below. Keep away. Replace the timing belt after every hours of operation. The Thermo--Sentry automatically resets after cooling down. Open the outer brush doors. Pull the brushes out from the scrub head. SV-7 1. Activating the Hopper Door Switch to open or close the door will cancel the sweep or scrub systems and automatically selects HIGH engine speed.
Page Forward Propel reverse adjustment. The Tank Level Switch must be closed for five 5 seconds before any output is affected.. If the Recovery Tank is still at least half full after the cycle, another 30 second cycle will begin. Green Blue Purple The Solution Valves will function only while Gray propelling forward or reverse during scrub operation.
Lift Cyl. Side Sq. Page HYDO. Page Fill the engine with oil until the oil is between the indicator marks on the dipstick. DO NOT fill past the top indicator mark. The engine oil capacity for Mitsubishi engines is 4. Page Lubricate the torque tubes after every hours and repack and adjust every hours of of operation. The torque tube grease fittings on operation. Page Drain and refill the hydraulic fluid reservoir with TennantTrue premium hydraulic fluid after every hours of operation.
Hot surface. NOT touch. Replace the hydraulic strainer outlet after every hours of operation. Page hours of operation. Check the radiator hoses and clamps after every hours of operation. T ighten loose clamps. Replace damaged hoses and clamps. Check the radiator hoses for cracks and deteriation after every hours of operation. Page 5 kg 8 to 1 O lb applied at the mid-point of the hours of operation.
Keep area well ventilated. Page Replace the spark plugs after every hours of operation. Page kPa psi of air pressure and press the reset button to manually reset the never hold the nozzle closer than 50 mm 2 in to breaker.
This may be done with the dust filter in the machine. Page 1. Raise the scrub head. Open the outer brush doors. Page After 8. Reinstall the brush idler plates. Close the inner and outer brush doors. Please try again. Increase visibility with cab-forward design, open sightlines, and steering-wheel-mounted controls. Provide an easy operator and maintenance experience with intuitive controls and easy-to-identify yellow touch points.
Sound Level: As low as 84 dBA. Save on chemical purchasing, storing, handling and mixing with water-saving ec-H2O technology , which electrically activates water into an innovative cleaning solution. Protect your asset from damage upon impact with a heavy-duty wraparound steel bumper and optional rear squeegee guard.
Operate safely and comfortably with open sightlines, spacious operator compartment and full front shroud. Protect operators from falling objects and debris with an optional overhead guard. Enhance Facility Image Achieve consistent cleaning results, even in the toughest industrial environments, with the effective sweeping and scrubbing capabilities of this ride-on sweeper-scrubber.
Get a total floor clean with excellent sweeping, scrubbing, water recovery and edge-cleaning performance. Easily blast-clean hard-to-reach areas with the optional high-powered pressure washer. Protect your facility and machine from damage with cushioned corner rollers. Transform cleaning operations with optional Pro-Panel technology, which integrates multiple cleaning settings and on-demand videos into an intuitive, highly visible touchscreen interface.
Easily care for solution and recovery tanks with design that allows for complete visual inspection and cleanout. Hopper Door Closed Reverse Propel Shutdown Relay Shutdown Mode Starting System On Glow Plugs On Solution V alves Fast System On Engine Oil Pressure, T emperature,. And Mil System Engine Oil Pressure And. T emperature Sensor Fuel Pump
0コメント